15 Fix Motorcycle Gas Tank Dent

This was a complex dent to repair. Tried the 12 Harbor Freight kit replaced their supplied hot glue with epoxy worked until the pullers shear.

Fixing A Dented Gas Tank Yamaha Fz6 Forums Fz6 Motorcycle Enthusiasts Forum

Your dent in your gas tank is carefully removed with custom designed steel rods that gain access behind the dent.

15 fix motorcycle gas tank dent. A difficult area on a gas tank to repair. I had a compressor of my own and blew out dents for my mates without much problems. If you guys have any questions leave it in the co.

Motorcycle Gas Tank Dent Repair Cost. The idea is to have the extreme temperature change make the dent pop back into place. Here are the steps watch the included video if you dont want to read.

The total cost of repairing dents in your gas tank will vary depending on which method you go with. How To Remove Dents From Motorcycle Gas Tank. Then you just use floss to remove it and a hair dryer to melt the glue off.

With paintless dent repair the best way to make the repairs is to push the dents out from the back side of the panel. Step aside and allow the flame to burn out burning all the fuel. At PCH Dent Repair we have the skills and experience when it comes to your motorcycle gas tank repair.

Fixing a dent on a motorcycle gas tank is as easy. Body shops sometimes use a small sheet metal screw and a slide hammer to pull out dents. If you take the tank to a professional body shop youll likely spend at least 200 to 300.

Since there is fuel in the tank and the access to remove the dent is not possible through the fuel filler hole we then use a special pulling method from the outside of the panel. Nose around marinas and boat repair shops lotsa them round our area the common opinion I got was any good 2 part marine epoxy is about the best fix for deep dents in tanks. My Tips Gas Tank Supply.

Bondo can go over the top of paint or primer and will hold but on bare metal is best. Use a grit somewhere in the 80-200 range to get enough grain in the surface for the Bondofiller to. Slowly your dent is removed without harming your factory or custom finish.

A super sharp and deep crease. I have also tried using dent repair kits. Ive heard of guys filling tanks with water and putting them in the freezer and stuff to try to get dents out.

Learn how to completely remove a dent small or big from a motorcycle gas tank using 2 different methods. Sand the bare metal or paint. Or you can use a pop rivet to pull a dent then grind it off when your done.

Air pressure might exert equal pressure on each part of the tank like the freezing water would. Ive heard depending on the location and dent you can put a dolop of hot glue in the center put a 1x1 on it till it dries then you just tug and it could pop it out. The third theory to remove a dent in a motorcycle gas tank is by heating up that spot of the tank using a hair dryer or something similar and immediately spraying it with freeze spray.

Motorcycle Gas Tank Dent Excel Removal Paintless Repair Mn. If youre repairing and painting the tank yourself you can expect to spend anywhere from 50 to 100. Of course with a tank this bad nothing could hurt to try.

Point its nozzle at the dent. However for some makes we may be able to perform the motorcycle dent repair with the tank. With a Harley Davidson we will require your tank off the motorcycle.

Now the tank is safe to work with. Before you call the repair shop try to get the dent out yourself using this auto dent repair trick that pops out dents without doing any damage to the paint job. Motorcycle Dent Repair Transcendent Paintless Removal Inc.

Use a hair dryer to heat the surface. Having a dented motorcycle gas tank repaired professionally is expensive not to mention that youll be without your bike while its in the shop being fixed. Im just concerned about the paint cracking.

It aint a bad fix if ya cant find a tank reasonably. I never tried it and Ive heard it wont work judging from the sohc4 forum Im on. One good way of removing a dent is to take it to a garage and blow it out with the compressor this will work on large dents to and some creaseswhich are usually a cnt to get out.

Depending on the tank itself the dent removal process can take between 1-4 hours. Of course you end up with a hole to be plugged when your done. You may be able to pull the dent out and repair the tank with a little body putty if you know what your doing.

We gently apply pressure against the damaged area. Paintless motorcycle tank dent repair is the preferred and most cost-effective method to protect your factory or custom finish. Motorcycle Dent Repair Faq.

And white like your scoot is easy to shoot if ya get it filled and shaped up nicely. Empty it and throw in a lighted match. Before you do anything make sure to burn the leftover fuel in the tank.

Motorcycle Dent Repair Transcendent Paintless Removal Inc. Its holdin up nicely for me.

Motorcycle Fuel Tank Repair Off 71 Medpharmres Com